The Glue Down Method of Installing Hardwood Flooring

Down the glue method of installing hardwood flooring Toronto is one of the first ways of installing hardwood flooring. If you want to know the fundamentals of how to install hardwood floors using the adhesive down method, you’ve come to the right location. One of it yourself hardwood floors, those done using the adhesive down method may be the most stable and enduring. Whenever you’re installing hardwood floors working with the adhesive down method, you may rest assured that you’re using a technique that has been time-tested.

Tools Needed When Installing Hardwood Flooring

Square Notched Trowel – This trowel should have one quarter inch sides for the application of the adhesive.

Broom and Dust Pan – You’ll want to always be cleaning up any saw dust that could get stuck beneath your floor panels or get trapped in your linking joints. The last thing you need is a prefinished hardwood floor when you are done installing hardwood floors.

Carpenter’s Crayon – This is what you use to indicate where you are going to make your cuts on your own panels. You’ll also use this to indicate up the surface at which you’re going to be placing your panels. You’ll want to keep this handy at all times because it is very important with the glue down method that all be done very precisely.

Circular Saw – You’ll use your circular saw to cut panels up as required. Additionally, you’ll use your circular saw to evaluate your substrate sheets every eight inches. This is important for preventing curling panels.

Glue – Many wood plank kits come with their own glue. If you have to purchase adhesive for your hardwood panels, I highly suggest Bostik’s Best Adhesive.

Lace Nails – You’ll use these nails when linking the panels into walls and walls strips.

Plywood Substrate Sheets – These are set on top of the concrete and go beneath your hardwood floor.

Soft Cloths – You’ll need these to clean up excess glue throughout the process of installing hardwood floors. If the paste is allowed to set, it’ll take additional step to remove it. Sometimes, it requires special compounds and paste to eliminate glue once it’s set. You will also need your soft cloths to wash up once you’ve installed your hardwood flooring.

Rubber Gloves – It’s much better to glue the fingers of your gloves together compared to your own fingers together! Anyway, many people don’t like having dried glue in their hands for weeks after they finish installing hardwood flooring.

While employing the adhesive down method for installing hardwood floors, it’s absolutely essential that the surface at which you’ll be putting your floors panels is properly ready. You’ll be attaching your flooring panels on this surface, so the floor has to be smooth, dry, and as clean as possible to give your hardwood floor a good support base. Be particularly careful to clean up anything that looks like it can be grease or oil, as your glue may not properly bond.

It’s also very important your sub floor be completely level and flat. If you observe any unevenness, get some patching cement from the hardware store to the sub floor.

You also need to pick between one of the two methods of laying hardwood panels down together with down the adhesive method. Your choices for installing hardwood flooring are the Walk On method or the Wet Lay technique.

If you opt for the Wet Lay way of installing hardwood flooring, you are going to be placing glue across the strand followed by placing the wood plank in addition to the adhesive. After the adhesive begins to become tacky, you proceed into another panel. But at times it is advised for first-time installers using the glue down method to put the next panels before the adhesive gets tacky so that you can correct your panels a few minutes after if they are not lined up properly.

The Walk On method of installing hardwood flooring requires precise panel laying. This procedure for installing hardwood flooring waits until the glue is very tacky and then lays the panel in the paste. This prevents you from becoming glue smudges all over your panels as you go. Experienced hardwood installers typically use the Walk On method because of the better finished results it can supply. As you’re reading instructions on how to install hardwood flooring, we will assume you are using the Wet Lay technique.

Instructions for Installing Hardwood Flooring

1. Place your substrate sheets, stretched across the base. Make sure that the surface is flat, clean, and free of debris.

2. Get your glue warm. If it’s below room temperature, you’ll discover that it’s impossible to operate together with your glue.

3. Utilize your square notched trowel to place glue in the beginning corner of the room. Place sufficient to securely fasten the board, but ration your adhesive so that it’ll be able to finish the whole hardwood flooring procedure. In the event that you had any doubt about whether you have enough glue, it would have been a fantastic idea to buy more before you started gluing. You’ll typically find that it requires an excess day to do the flooring when you run out of glue before you’ve finished.

4. Attempt to put your initial wood plank straight down to the glue, secured into the corner. As you are working with wet adhesive, place the panel as best you can initially so that you’ll not be smearing the glue around as you adjust the panel’s positioning. In the event that you had used the Walk On method, you wouldn’t have the ability to move the panel at all only a few seconds after placement.

5. You can continue on as in the above steps with adding more panels until you get to the last panel, which shouldn’t completely fit. Use your crayon to mark where to cut the plank and your saw to make the cut.

6. Get your first row wedged in very tight so that it will provide a solid foundation for your whole floor.

7. Before any of the paste dries, use a soft cloth to wash up any glue that may be sitting on the surface of your first row. The longer you wait to clean up the paste, the more difficult it will get to clean up the paste.

8. Hopefully you did not mutilate the excess piece of panel that you cut off to end the first row. That’s going to be the panel that you use to start another row. This helps ensure your hardwood floor looks fine by having all the panels offset.

9. If you are visiting any bubbles, hills, or slopes around the panels you have been laying, set a thick, horizontal object in addition to these sections to keep them down until the adhesive attaches them into the substrate.

10. Clean up again. Get all of that sawdust and glue out of there. A soft fabric with mineral spirits onto it may be employed to get glue you’ve missed that might be hardening. Clean the mineral spirits off quickly to prevent having them damage the floor. You should have a fine, new hardwood flooring.

-For optimum results, use plywood sheets to make your substrate.

But you should still attempt to get the surface as much as possible before laying your substrate sheets.

-If you have sufficient flat, heavy objects, set them on each panel as you place the panel on the floor to allow it to get the greatest possible attachment to the substrate. Don’t use anything which may damage the surface of your panels. In case you have nothing else, you can always lay on the panels. Take care not to get glue on top of them though.